milwaukeetool

2-Cutter SDS-PLUS Carbide Hammer Drill Bit Set (5-Piece)

2-Cutter SDS-PLUS Carbide Hammer Drill Bit Set (5-Piece) - Main image
2-Cutter SDS-PLUS Carbide Hammer Drill Bit Set (5-Piece)2-Cutter SDS-PLUS Carbide Hammer Drill Bit Set (5-Piece)2-Cutter SDS-PLUS Carbide Hammer Drill Bit Set (5-Piece)2-Cutter SDS-PLUS Carbide Hammer Drill Bit Set (5-Piece)2-Cutter SDS-PLUS Carbide Hammer Drill Bit Set (5-Piece)
$4.99 In stock

Category: Factory Clearance Sale

The Milwaukee 48-20-7490 is a 5-Piece Carbide 2-Cutter SDS Bit Kit. Milwaukee's 44 Magnum series carbide drilling bits offers a unique multi-faceted carbide insert reducing the breakage possibility when drilling through re-bar and mesh. The distinctive chisel shaped tip breaks concrete quickly for faster penetration. The 4-fluted spiral shaft has improved dust removal resulting in less bending stresses. Available in diameters from 5/32 in. to 5/8 in. Assortment of 5 bits.
  • Assorted diameters
  • SDS shank
  • 2-cutter head
  • Drilling depth
  • Assorted lengths
  • Carbide construction

    • Customer Reviews (4.8 / 5 · 50 reviews)

    Isabella V. ★★★★★

    These bits punched through the concrete in my basement wall with far less effort than my old set. The carbide tip seems genuinely tough, and they haven't chipped after a dozen holes.

    David ★★★★★

    Drilled through reinforced concrete for the first time yesterday and the carbide tip didn't chip at all—the multi-faceted insert really seems to hold up. These bits cut smooth and fast in my rotary hammer.

    Alexander T. ★★★★★

    I was a little skeptical about the carbide tip holding up, but after driving a dozen holes into reinforced concrete block, the cutting edge still looks brand new. The dust extraction slot on the side actually works well, keeping the hole clear as I drill.

    Owen I. ★★★★★

    These bits chew through the masonry in my old basement walls like butter, and the SDS shank stays locked tight no matter how much I lean on it. Really glad I grabbed a set while they were clearing them out.

    Joshua R. ★★★★★

    Drilled into reinforced concrete for the first time today and the 2-cutter design really makes a difference—the bit stayed cool even after multiple holes. The 5-piece set covers the sizes I use most for anchor installs. Already ordered a second set for my work trailer.

    Zoe ★★★★★

    The carbide tip on the ¾-inch bit chewed through a concrete lintel without any wobble, which was a huge relief. I’d been dreading that job with my old bits. Only wish it came in a hard case instead of the plastic sleeve.

    Ryan Q. ★★★★★

    First hole I drilled with the ½-inch bit went through old concrete like butter, and the carbide tip still looks brand new. This set handled rebar without chipping, which my old bits definitely struggled with.

    Hannah ★★★★★

    I’ve been using this set to drill into old concrete block, and the 2-cutter design really keeps the bit from wandering off center. It’s nice that the carbide tip seems tougher than the last set I had, so I’m not replacing one after a few uses.

    Ella X. ★★★★★

    These punched through the reinforced concrete in my basement wall without even slowing down. The two-cutter design really does seem to clear the dust better than my old bits, and the set covers all the sizes I typically need.

    Robert ★★★★★

    I was skeptical about carbide bits after some bad experiences, but the 2-cutter design on these really slices through brick and block cleanly without wandering. Finish on the holes is surprisingly smooth, which saves me patching time.